M10 x 43mm Inside (W) x 125mm Length (L) A2-70 G304 Stainless Round U Bolts & Crimp + Plate & Nuts

About Round U Bolts with Plate

Round U Bolts with Plate are complete pipe-clamp sets: a round-bend U bolt, two matching hex nuts, two washers, a mounting plate with pre-drilled bolt holes and two crimps. The crimps are curved saddles that sit between the plate and the pipe - they stop the plate sliding down the pipe under load and spread the clamping force across a wider arc. Used to clamp round pipe, tube, conduit or rod to a flat surface without site-fabricating a backing plate. Sold as a single SKU so the plate, U bolt, nuts, washers and crimps are all matched for size and finish. Made to the Inox World Standard in stainless A2-70 G304 for outdoor, food-grade, marine and chemical-exposure use.

Frequently Asked Questions

Material & Coating

Stainless A2-70 G304 Austenitic stainless steel. Property class 70 designates a minimum tensile strength of 700 MPa with a 0.2 percent proof stress of 450 MPa. Lightly magnetic in cold-worked form, which does not affect corrosion performance.

Important Do not pair stainless fasteners with plain or galvanised steel components in wet service. The galvanic potential difference accelerates corrosion of the less-noble metal.

Class Stainless fasteners are classified by property class: A2-35 / A2-50 / A2-70 in G304 stainless, and A4-40 / A4-70 / A4-80 (Bumax 88) in G316. The first digit indicates the alloy and the second is the minimum tensile strength in 100 MPa increments (e.g. A4-70 = 700 MPa). See the head marking chart and full strength table.

Thread Pitch & Terminology

Thread Pitch (Metric) Metric fasteners measure thread pitch as the distance between thread peaks, expressed in millimetres. Metric also branches into three series: coarse (the default; widest tolerance, easiest to tap), fine (a tighter pitch for higher clamp load or thinner walls), and extra fine (the tightest pitch, used for thin-wall tube, precision instruments, and aerospace fittings where vibration loosening must be minimised). Always match the series as well as the size - a metric fine nut will not engage a metric coarse bolt of the same diameter, and an extra fine nut will not engage either. This product has a 1.50mm coarse pitch, meaning the peaks are 1.50mm apart.

How to Measure

Three numbers The inside width between the legs (measured across the straight section, not the bend), the leg length from the inside crown of the bend to the leg end, and the diameter across the outside of the thread - expect the reading a touch under the nominal size (an M10 reads between about 9.7mm and 10mm). The identification box near the top of this page shows all three on the drawing, and our U bolt measuring guide walks through them step by step.

Resources

Pricing & Delivery

Includes GST, a Tax Invoice and Free Standard Delivery anywhere in Australia.

Buy with Confidence

15+ years selling online · 25,000+ stock lines · 200 million pieces ex-stock in Brisbane QLD.

Disclaimer

Technical data Researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately.

Measurements Sizes are taken from supplier catalogues or hand-measured and should be used as a guide. Minor variation between batches is normal. Stock is sourced from various suppliers, so differences may exist between batches in thread length, markings, appearance or finish.

Product Photos & PDF Data Sheets Represent the product type, not exact size. PDFs are a reference guide only. Specifications may change without notice.

If you see any problems with any of our specifications or you require additional information please contact us.